Medallion Bagger Bedienungsanleitung PDF herunterladen

Medallion Brand

Premium Bagger Gauges

Operation Guide

The battery icon is displayed when the battery voltage to

the tachometer reaches 12.4 VDC with the engine running

and 12.1 VDC when the engine is not running.

Is displayed when cruise is turned on. The little arrow on

the upper left side of the icon is present when cruise is

engaged.

It does not matter if you have a 5-speed or 6-speed. If

the ECU does not broadcast gear information, the gauge

can be trained quickly to learn which gear you are in. If

the ECU does broadcast the information, the gauge is

ready to use.

[See the Setup Menu Below.]

Current Gear Position Display

1) Power up the gauges.

2) Hold both buttons for about 2.5 seconds until the LCD displays "SETUP" and the setup

menu is displayed.

3) Press the LEFT ('NEXT') button to scroll down the menu items until "SET ODOMETER" is

highlighted, then press the RIGHT ('SELECT') button.

4) One of three possible messages will now be displayed:

a) If One Time Programable [OTP] odometer has not been set and less than 100mi

have accumulated,since installing the gauges the LCD will display "Odometer can be set

ONCE in first 100mi." Pressing the LEFT ('CONTINUE') button continues to step #5.

Pressing the RIGHT ('CANCEL') button returns to the setup menu.

b) If OTP odometer has already been set, the LCD will display "Odometer has already

been set once. Press a button to return to the setup menu." Pressing either button returns to

the setup menu.

c) If 100mi has accumulated without setting the OTP odometer, the LCD will display

"Odometer set ability has expired. Press a button to return to the setup menu." Pressing

either button returns to the setup menu.

5) The LCD now displays the current odometer value as "ODOMETER: xxxxxxmi" or

"ODOMETER: xxxxxxkm" depending on units. Button presses are as follows:

a) Pressing the left ('DEC') button decrements by 1 mi/km.

b) Pressing the right ('INC') button increments by 1 mi/km.

c) Holding either button decrements/increments by 1 mi/km until the odometer is

divisible by 10, then by 10 mi/km until the odometer is divisible by 100, then by 100 mi/km

until the odometer is divisible by 1000, then by 1000 mi/km thereafter.

d) When desired odometer value is displayed, holding both buttons ('<- SAVE ->') for

about 2.5 seconds saves the odometer value and returns to the setup menu.

NOTE: Once the odometer has been saved, no additional programming can be performed

and the odometer value is permanently stored.

Note: Odometer programming must be completed

within the first 100 miles after installing

Factory programmed to display when the fuel level

reaches 20%.

Low Fuel Icon

LCD Symbol Description

Cruise Control Icon

Low Battery Icon

ENGAGED

Technical Support Contact Information:

Technical Support | 616.847.3700 | techsupport@medallionis.com

Harley-Davidson ®, Street Glide®, and Road Glide® are registered

trademarks of Harley-Davidson Motor Company, Milwaukee, Wisconsin, USA

Date: 6800-09506-01REVB

Setup Menu

To enter the SETUP menu, push and hold both buttons until the LCD displays the word

SETUP. The right button changes the option highlighted, the left button scrolls down to

the next option

Clock, ODOmeter, Trip A, Trip B, SERVice alarm

Bike Odometer [See Setting Odometer Below.]

Trip A is resettable and independent from Trip B. While Trip A is

displayed, pressing the right button resets TRIP A odo. While Trip B is

displayed, pressing the right button resets TRIP B odo.

Service reminder. This can be set to any mileage. Default from the

factory is 500 miles. Pressing and holding the right button allows

adjustments.

12 or 24 hour clock available. Setting the clock (LCD Display), press

and hold the right button until “12-HOUR” appears. The left button

adjusts value, the right button selects the next mode. If no buttons are

pressed in five seconds, the new clock setting will be stored.

LCD Display Mode

BIKE - This will adjust the gauge system to operate with the correct fuel tables and other

features that are model year dependent.

UNITS - This changes between English and Metric units displayed on the LCD

AUTO DIM - Auto Dim turns the daylight sensor on or off enabling the LCD display and

icons to dim down at night.

SHIFT ICON - The Shift icon is an up arrow that lights up when engine RPM reaches

it’s set point. This shift point is programmable.[See Setting Odometer Below.] This shift icon

can be set to “flash” or “solid”.

GEAR SOURCE - This tells the gauge where to get the gear position. On some bikes

the 6th gear is not broadcast. Changing to “gauge” and going through the learn mode will

enable gear position. NOTE: gear position is only displayed while engaged in a gear.

DEMO MODE - This mode is for table top demonstration only. This mode can be

enabled, but will NOT operate if the Handlebar Control Module is connected. In this mode the

gauges will move through the gears and display icons

SET SHIFT ICON RPM - The shift icon can be setup to light at any RPM. This is

adjusted by 50 RPM steps. Press the RIGHT button to adjust up, and the LEFT button to

adjust the RPM value down. Do not press any buttons for 5 seconds to save settings.

START GEAR LEARNING MODE - Read below for specific instructions

RESTORE DEFAULTS - If something is misadjusted or programmed incorrectly,

your gauge can be restored to the original factory settings by highlighting RESTORE

DEFAULTS and pressing the RIGHT button .

GAUGE INFO - This menu displays the software version and build date of the gauge.

DIAGNOSTICS - This is the factory menu for diagnosing problems in the

instrumentation system. The first page shows the raw values that the microprocessor is

looking at. Additional pages are entered by pressing either button. On the second page is

the gauge values being sent to the gauges. The third page displays if the gauge is seeing

any data on the serial data bus from the engine.

EXIT - Pressing the RIGHT button will cause the gauge to save any changes and then

reset gauge.

PRESS BOTH

AT SAME TIME

SCROLL DOWN CHANGE VALUE

START GEAR LEARN MODE - INSTRUCTIONS

If your ECU does not broadcast the current gear, you can program the

gauge to display which gear you are in. Select this mode by pressing the

RIGHT button.

START - Begin driving down the road at a steady speed in 1st gear

(need to hold +/- 2 MPH).

PRESS EITHER BUTTON AT

ANY TIME TO EXIT LEARNING MORE

START LEARN MODE

LEARNING - Once the gauge has learned the gear, it will display

SAVED. You must then Shift to the next gear

LEARNING next gear - Continue driving down the road at a

steady speed (need to hold +/- 2 MPH). Until the SAVED appears. Continue

through all of the bike gears. If you need to stop or exit this mode press

either button.

SHIFT

BIKE

GEAR

*Bike 2008 or newer

*Units: English

*AutoDim: Enabled

*Shift Icon: Flash

*Gear Source: ECU

*Demo Mode: Disabled

Set Shift Icon RPM: 3000RPM

(Note: this item is not reset with the factory reset function)

Start Gear Learn Mode

Set Odo

*Restore Defaults –

(Note: only lines with * will be restored to factory settings)

Tach Info

Fault Codes

Diagnostics

Exit

FACTORY DEFAULTS

1 2

Inhaltsverzeichnis

Seite 1 - Setup Menu

Medallion Brand Premium Bagger Gauges®Operation GuideThe battery icon is displayed when the battery voltage to the tachometer reaches 12.4 VDC with th

Seite 2 - Installation Instructions

Medallion Brand Premium Bagger Gauges®Record the mileage on the existing gauge.Remove the inner fairing screws. TIP: Sometimes these are hard to find.

Weitere Dokumente für Autolautsprecher Medallion Bagger

Um das Dokument anzuzeigen Medallion Bagger Bedienungsanleitung

Medallion Bagger Bedienungsanleitung (14 Seiten)

Um das Dokument anzuzeigen Medallion Bagger Wartungshandbuch

Medallion Bagger Wartungshandbuch (144 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Medallion Bagger Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Autolautsprecher Medallion Bagger herunter. Medallion Brand Premium Bagger Gauges Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Autolautsprecher Medallion Bagger

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Autolautsprecher Medallion Bagger